Buffalo 16×24 Pneumatic Dual Platen Heat Press with Laser Alignment
$1,999.00
- Large 16 × 24-Inch Platen: Handles oversized garment graphics, DTF transfers, sublimation jobs and other flat applications with room for efficient production.
- Dual-Station Workflow: Prepare the next item on one lower platen while the other station is pressing to reduce idle time during repeat orders.
- Consistent Pneumatic Pressure: Adjustable air-powered operation supports repeatable pressure up to 0.8 MPa without requiring the operator to close a manual lever.
- Infrared Laser Alignment: Position transfers more consistently using the integrated alignment reference before beginning each automatic or manual press cycle.
- Commercial 110V Configuration: Uses a 2 kW, 18A electrical system on a dedicated 20A circuit and requires a compatible external air compressor, sold separately.
Buffalo 16×24 Pneumatic Dual Platen Heat Press
The Buffalo 16×24 pneumatic dual platen heat press is built for apparel decorators and production shops that need a larger pressing area, repeatable air pressure and a faster two-station workflow. Its 16 × 24-inch heated platen supports oversized DTF transfers, sublimation graphics, heat-transfer vinyl and other compatible flat heat-transfer applications.
Two lower workstations let an operator prepare the next item while another item is being pressed. The up-sliding pneumatic head can run in automatic or manual mode, while infrared laser alignment helps position transfers before the cycle begins.
16×24 Heat Press for Larger Transfers
The 16 × 24-inch platen provides more working area than common 15 × 15-inch or 16 × 20-inch presses. That additional space is useful for oversized shirt graphics, hoodies, tote bags, mousepads, flat sublimation panels and other products that fit safely within the machine’s clearance and application limits.
The listed maximum item thickness is 2.36 inches. Operators must still follow the transfer-material manufacturer’s recommended time, temperature and pressure and verify that each substrate is rated for heat pressing.
Dual-Station Pneumatic Production
The two-station layout is designed to reduce waiting between cycles. While one item is under the heated platen, the operator can load and align the next item on the opposite workstation.
Pneumatic pressure reduces the physical effort required by manual clamshell and swing-away presses. The regulator supports adjustable operating pressure, with the OEM platform rated up to 0.8 MPa. Consistent results still depend on correct setup, platen condition, compressor output and transfer instructions.
Automatic and Manual Operating Modes
The digital controller provides time, temperature and production-count settings. In automatic mode, moving the press head fully into position initiates the programmed cycle; manual mode gives the operator direct cycle control for setup and testing.
An emergency-stop control allows the operator to interrupt operation. All users should receive training and keep hands, garments and loose objects clear of moving and heated components.
Infrared Laser Alignment
The integrated infrared positioning system provides a visible alignment reference for transfer placement. This is especially helpful for repeat logos, left-chest graphics and production runs where consistent placement matters.
The laser is a positioning aid rather than an automatic vision system. Operators should create and verify placement templates for each garment style and size before production.
Adjustable Pneumatic Pressure
The air-powered pressure system is designed to apply repeatable force across compatible flat products. Pressure is adjusted at the regulator and monitored on the gauge, allowing the operator to match the setup to the transfer and substrate.
The OEM platform lists a maximum pressure of 0.8 MPa, while normal working pressure is commonly set lower according to the application. Always begin with the transfer supplier’s instructions and test before starting a production run.
Electrical and Air-Compressor Requirements
This Buffalo configuration is designed for 110V/60Hz power and is rated at 2 kW and 18A. It requires a properly grounded dedicated 20A circuit with the correct receptacle. Have a qualified electrician confirm the installation before connecting the machine.
An external air compressor is required and is not included. The referenced OEM configuration recommends an oil-free compressor with approximately an 8-gallon tank, maximum 120 PSI and output of 4.0 CFM at 90 PSI. Confirm the final Buffalo production-unit requirements before purchasing a compressor.
What’s Included with the Buffalo Dual Platen Heat Press?
- Buffalo 16 × 24 pneumatic heat press assembly with heated upper platen
- Two 16 × 24 lower workstations with heat-resistant pressing surfaces
- Integrated stand and locking casters for stable placement and controlled movement
- Digital time and temperature controller with production counter
- Pneumatic regulator and pressure gauge
- Infrared laser positioning system
- Emergency-stop control
The external air compressor, transfer materials, garments, electrical installation and freight-unloading equipment are not included. Buffalo Imaging should confirm the final loose hardware, fittings, hoses, tools, documentation and spare-parts packing list before publication.
Buffalo 16×24 Pneumatic Heat Press Specifications
| Spec | Detail |
|---|---|
| Brand | Buffalo Imaging |
| Buffalo SKU | BUF-HP-1624-PD-L-110 |
| Buffalo model / MPN | BHP-1624PDL |
| Private OEM platform | CH-6040-TD2L |
| Press type | Up-sliding pneumatic dual-station heat press |
| Heated platen size | 16 × 24 in / 40 × 60 cm |
| Lower workstations | Two |
| Operating modes | Automatic and manual |
| Positioning | Infrared laser alignment |
| Pressure system | Adjustable pneumatic pressure; up to 0.8 MPa |
| Recommended normal pressure | Approximately 0.4–0.6 MPa; application dependent |
| Voltage / frequency | 110V / 60Hz |
| Rated power / current | 2 kW / 18A |
| Required circuit | Dedicated grounded 20A circuit; verify receptacle and code requirements |
| Temperature range | 0–570°F / approximately 0–299°C |
| Timer range | 1–999 seconds |
| Maximum listed item thickness | 2.36 in |
| Controls | Digital time, temperature and cycle-count controller |
| Safety control | Emergency stop |
| Air compressor | Required; not included |
| Referenced compressor recommendation | Oil-free, approximately 8-gallon tank, 120 PSI maximum, 4.0 CFM at 90 PSI |
| Approximate assembled dimensions | 35 × 33 × 52 in; confirm production unit |
| Approximate net machine weight | 286 lb; confirm production unit |
| Gross shipping weight | 306.5 lb |
| Packed dimensions | 42.5 × 33.9 × 32.3 in |
| Shipping method | LTL freight / crated |
| Warranty | Buffalo Imaging warranty term to be confirmed before publication |
| UPC / GTIN | Not assigned |
Built for DTF, Sublimation and Production Apparel Shops
This Buffalo dual-platen heat press is best suited to businesses that have sufficient floor space, a compatible compressed-air supply, an appropriate electrical circuit and a repeat-production workflow. Browse more commercial heat presses or pair the press with equipment from Buffalo Imaging’s DTG and DTF printer collection.
For electrical, compressor, freight or installation questions, call Buffalo Imaging at 323-721-5678 before ordering.
What is the Buffalo 16×24 pneumatic dual platen heat press used for?
It is designed for professional heat-transfer production on compatible flat products, including DTF transfers, sublimation graphics and heat-transfer vinyl. The 16 × 24-inch platen is especially useful for oversized apparel designs, hoodies, tote bags, mousepads and other products that fit within the machine’s clearance.
How does the dual-platen design improve production?
The press has two lower workstations. An operator can load and align the next item on one station while the other item is being pressed, reducing idle time between repeat jobs without requiring two heated upper platens.
Does the Buffalo dual-platen heat press require an air compressor?
Yes. The pneumatic system requires an external air compressor, which is sold separately. The referenced configuration recommends an oil-free compressor with approximately an 8-gallon tank, a maximum rating of 120 PSI and output around 4.0 CFM at 90 PSI; confirm the final machine requirements before purchasing the compressor.
What electrical connection does the Buffalo 16×24 heat press require?
The verified configuration is rated for 110V/60Hz, 2 kW and 18A and requires a properly grounded dedicated 20A circuit. Have a qualified electrician verify the receptacle, wiring and local electrical-code requirements before installation.
Does this heat press operate automatically?
It supports automatic and manual operating modes. In automatic mode, moving the press head fully into position starts the programmed pressing cycle; manual mode is useful for setup, testing and direct cycle control.
What does the infrared laser alignment system do?
The infrared positioning system projects an alignment reference that helps the operator place transfers consistently before pressing. It is a placement aid, not an automatic camera or vision system, so operators should still create and test templates for each garment style and size.
What pressure, temperature and time ranges are available?
The pneumatic system is rated for adjustable pressure up to 0.8 MPa, with approximately 0.4–0.6 MPa commonly used as an operating range depending on the application. The digital controller supports temperatures up to about 570°F and a timer range of 1–999 seconds. Always follow the transfer supplier’s instructions.
How thick of an item can the Buffalo heat press accommodate?
The listed maximum item thickness is 2.36 inches. Actual suitability also depends on the material, shape, platen contact, required pressure and heat tolerance, so test unfamiliar substrates before production.
What is included with the Buffalo pneumatic heat press?
The system includes the Buffalo-branded pneumatic press assembly, one 16 × 24-inch heated upper platen, two lower workstations, integrated stand with casters, digital controller, pneumatic regulator and gauge, emergency-stop control and infrared positioning system. The external compressor, electrical installation, garments and transfer materials are not included.
How large and heavy is the press, and how is it delivered?
The assembled machine is approximately 35 × 33 × 52 inches, subject to final production verification. It ships crated by LTL freight at approximately 306.5 lb gross with packed dimensions of 42.5 × 33.9 × 32.3 inches, so customers should plan for delivery access, unloading and placement before ordering.
| Brand | Buffalo Imaging |
|---|---|
| Press Type | Flat Press |
| Platen Size | 16" x 24" |
| Operation Type | Semi-Automatic (Pneumatic) |
| Weight | 306.5 lbs |
| Dimensions | 42.5 × 33.9 × 32.3 in |
Add a review
Buffalo 16x24 Pneumatic Dual Platen Heat Press with Laser Alignment Your review
* Review is required
Name
* Name is required
Email
* Email is required
Reviews
There are no reviews yet