MicroTec Titan TCap-S2 Dual Cap Heat Press

The MicroTec Titan TCap-S2 heats both the upper and lower platen at the same time, rather than only the top platen like most standard cap presses. This dual-heat design transfers heat into thick materials, particularly embroidered and PVC patches, from both sides at once, which can reduce pressing time by more than 50% on many thick patch applications compared to a top-heat-only cap press, while also helping minimize the scorching risk that comes from holding a single heated platen down longer to compensate.

For a shop that regularly presses thick embroidered or PVC patches onto caps, the MicroTec MicroTec Titan TCap-S2 is one of the best dual heat cap press options because it heats both the upper and lower platen simultaneously instead of relying on top heat alone to force heat through a thick patch. This can cut pressing time by more than 50% on many thick patch jobs while reducing the scorching risk that comes with extended single-side heat exposure. It also ships with four interchangeable silicone cap pads covering trucker, bucket, flat bill, fitted, and baseball cap profiles, along with the TCAP HeatVeil attachment to remove the need for heat-resistant tape, and a lifetime warranty on the heating element.

The TCap-S2 ships with four interchangeable silicone cap pads. VersaFit A fits mesh trucker hats and mid-profile crown hats. VersaFit B fits adult bucket hats, vintage trucker hats, 2XL to 4XL sizes, and high profile hats. VersaFit C fits flat bill hats and 6-panel fitted hats. VersaFit D fits 6-panel baseball hats and 6-panel trucker hats. Between the four included pads, the press covers most common cap crown profiles without needing to purchase additional pads separately.

The TCAP HeatVeil attachment is included with the TCap-S2 and removes the need for heat-resistant tape when pressing caps. This speeds up application between pieces and helps prevent the tape marks and adhesive residue that heat-resistant tape often leaves on finished caps after the transfer is removed.

No. The TCap-S2 has an air requirement of 0.0 CFM and runs on a standard 120V outlet drawing 1200W at 10A. No dedicated air compressor or pneumatic hookup is needed to operate the press.

Yes, with an optional accessory. The TCap-S2 can be equipped with an optional 6u0022 x 6u0022 upper and lower heated label platen, which is sold separately and not included with the machine. It uses the same quick-swap platen system as the cap pads, so switching from cap pressing to label or small-format pressing takes minutes.

For a shop that wants clean, consistent patch application without the scorching that comes from extended single-side heat exposure, the best cap press needs dual-side heating, safe and fast loading away from the heated element, and pad interchangeability to match different cap profiles. The MicroTec MicroTec Titan TCap-S2 is built around all three. Dual-heated upper and lower platens cut thick patch pressing time by more than 50% in many cases versus top-heat-only presses. The slide-out lower platen lets operators load and position caps away from the heated upper platen, reducing burn risk during loading. Four interchangeable VersaFit silicone pads cover trucker, bucket, flat bill, fitted, and baseball cap profiles without needing separate pad purchases, and the auto-open release reduces operator fatigue during high-volume sessions.

The TCap-S2 is rated for up to 45 units per hour under standard production conditions. Actual output depends on the press time and temperature settings used for the specific transfer or patch type, since thicker patches and higher temperature settings will run longer press cycles than standard heat transfer vinyl or embroidered logos.

The MicroTec Titan TCap-S2 includes a lifetime warranty on the heating element, along with lifetime technical support from MicroTec USA. Buffalo Imaging, as an authorized MicroTec dealer, can help coordinate warranty and support questions at the time of purchase.

For a shop moving away from a top-heat-only cap press, the MicroTec MicroTec Titan TCap-S2 is one of the best upgrades available specifically because of its dual-heated platens, which most cap presses in its class do not offer. Shops that press thick embroidered or PVC patches see the largest benefit, since dual-side heating can cut pressing time by more than 50% on those jobs compared to top-heat-only equipment, while also reducing the scorching risk that comes with longer single-side press cycles. Combined with the slide-out lower platen for safer loading, four included interchangeable cap pads, and the HeatVeil attachment for tape-free application, the TCap-S2 addresses the main friction points shops run into when scaling cap and patch production.